Failed mastic and sealants cost UK building owners thousands in water damage and energy loss. Learn causes, warning signs, and preventive maintenance strategies.

Mastic and sealant failure is the loss of a joint’s weathertight seal, either because the sealant has pulled away from the substrate or because it has torn within itself. It is one of the most common causes of water ingress on commercial buildings, and it is also one of the cheapest defects to fix if it is caught before the water finds somewhere to go. GLRE carries out mastic and sealant repair at any height by rope access.
Sealant is the flexible joint between components that move at different rates. On a commercial facade it sits around glazing frames, along curtain wall joints, between cladding panels, at expansion joints and at roofline interfaces.
Its job is not simply to fill a gap. It has to stay bonded to two faces while those faces move apart and back together through every temperature cycle for years. That is why a rigid filler fails immediately and why sealant selection is a movement calculation rather than a preference.
Sealants are classified by movement capability under ISO 11600, the sealant classification standard. The class on the data sheet tells you how much joint movement the product will take. Specifying below the expected movement guarantees failure whatever the workmanship.
The most common cause. Sealant needs a clean, dry, sound surface to bond to. Applied over dust, contamination or damp, the adhesive bond never fully develops and the joint delaminates early.
On refurbishment this means the old sealant must be removed completely. Applying new material over aged material creates a weak interface that fails at the join. Partial overcoating without removal is not a lasting repair and is not a practice GLRE carries out.
A joint that is too shallow holds too little sealant to absorb the movement, so it tears. A joint that is too deep concentrates stress, particularly where three-sided adhesion occurs and the sealant bonds to the back of the joint as well as both sides, which stops it stretching at all.
Backer rod or bond-breaker tape controls the depth and prevents three-sided adhesion. The correct width-to-depth relationship is the one on the sealant manufacturer’s data sheet for that product, not a rule of thumb carried over from a different job.
UV hardens sealant, reduces flexibility and produces surface crazing that works deeper over time. Survey teams consistently find more advanced deterioration on south and west elevations than on north-facing ones, which follows from the exposure.
Temperature swings compound it. A facade expands and contracts daily and seasonally, and each cycle fatigues a material that UV has already stiffened.
Some plastics and rubbers contain plasticisers that migrate into sealant, softening it and destroying the bond. Applying silicone directly over aged EPDM gaskets is the classic example. The answer is complete gasket removal, or a bond-breaker tape between the two materials.
Good sealant fails when it is applied outside the temperature or humidity range on the data sheet, without backer rod, without proper tooling, or with a mixing error on a two-part product. None of these is visible once the joint is finished, which is why supervision during application matters more than inspection afterwards.
| What you see | What it means |
| A clean gap between sealant and substrate | Adhesive failure. The bond has gone: a preparation or compatibility problem |
| Tears or splits within the sealant itself | Cohesive failure. The material has lost elasticity or was under-specified |
| Yellowing, chalking or fine surface crazing | UV degradation. Cosmetic at first, then it works deeper |
| Water staining below windows or at mullions | Water has been getting in for some time already |
| Draughts near glazed facades in wind | Air leakage through failed perimeter joints |
| Darkening along a joint line | Moisture sitting behind the sealant |
Most of this is only visible at close range. A defect that reads as a shadow from the car park is a 4mm open joint from a rope. That is the argument for a proper facade inspection rather than a walk round the building.
The sealant is rarely the expensive part. The secondary damage is. Water entering through a failed perimeter joint stains finishes, soaks ceiling tiles and floor coverings, and reaches services that then need inspecting. On a curtain wall, water getting into the glazing pocket overwhelms drainage designed for small quantities and tracks inward through joints that were never intended to be the primary barrier.
Emergency work also costs more than planned work, for reasons that are structural rather than opportunistic: it is unprogrammed, it competes for availability after severe weather, and it disrupts occupiers who were not warned. Planned replacement avoids all three. GLRE does not publish a percentage saving, because the honest answer depends entirely on the building.
Where water has already reached the inside, leak investigation and repair comes before resealing, so the entry point is confirmed rather than assumed.
Above the first floor, rope access is the standard method for sealant work on commercial buildings. A technician can reach one failed joint on the eighth floor without mobilising access equipment across the whole elevation, which is what makes a targeted repair worth doing at all.
It also suits irregular facades where scaffolding fits badly, and it mobilises fast enough to matter when water is already coming in. The wider case is set out in rope access and industrial abseiling and compared against scaffolding in the rope access versus scaffolding article, and the standards it works to come from IRATA International.
For any commercial building with a sealed facade, yes. Inspection on a set interval identifies deterioration while it is still a sealant job rather than a water damage job, and it lets the cost be budgeted rather than absorbed as an emergency.
Exposure sets the interval. A coastal, industrial or high-exposure urban building needs looking at more often than a sheltered one. The right frequency comes out of the first survey, not out of a table.
For landlords and facilities teams there is a second benefit. A documented maintenance record supports lease obligations, insurance requirements and dilapidations assessments, which is what health and safety inspections and reports are written for.
The longer version of that checklist is in how to choose a rope access contractor. GLRE holds CHAS Elite, SafeContractor and Constructionline Platinum, all operatives are IRATA certified, and the completed projects page names buildings including Alexandra Palace and Mander Shopping Centre.
Seeing cracked joints, staining or draughts on a commercial facade? Contact GLRE to book a free sealant condition survey.